Sheet Metal Brakes

Our Hand Brake Sheet Metal Brake and Box And Pan Brakes are built to the highest quality specifications with quality features such as hardened bending rails and heavy all steel frames with heavy duty truss rods and braces for long life and less deflection across the apron when bending; the box and pan brakes have hardened fingers that produce minimal deflection, even when bending boxes up to 4 or 6 inches deep depending upon the model. The hand brake is available with a 48 inch wide bending capacity, and the Box and Pan Brakes are available in widths of 48 inches (2 models), 72 inches, 96 inches, and 120 inches.

Click Here To Expand This To A Full Page Version

To See Other Products - Click Here To Go To Our Index

BB-4812 Box And Pan Brake

HB-4816 Hand Brake

BB-7212 Box And Pan Brake

BB-9612 Box And Pan Brake

BB-12014 Box And Pan Brake


  • Features/Specifications


    • See all the features, specifications, and prices below. If you need additional information to order, then purchase any of the video(s) listed below for download to your computer. Click on the video order form link directly below and type in the selections you want. Videos will be e-mailed to you.

  • Video No. SMBP1-2: Video on operation of sheet metal box and pan brakes, running time is 3 min. 22 seconds - Price is $7.50



  • Features/Specifications - BB-4816

    • BB-4816 Box And Pan Brake
  • BB-4816 Box And Pan Brake can accept 48 inch wide sheets of mild steel with thicknesses of up to 16 gauge across the entire width of its apron

  • Includes a heavy counter weight to assist lifting the apron even when bending at full capacity

  • Maximum lift of beam is 1 3/4 inches, beam adjustment is 5/8 inches

  • This Box And Pan Brake can bend with no deflection because the heavy duty truss rod system is further supported by an all steel frame that is electro welded and the bending fingers are hardened, which creates straight edges on the tightest of bends.

  • This finger brake has five 2 inch, six 3 inch, and five 4 inch fingers allowing the operator to configure for most box and pan layouts. The fingers on the BB-4816 can be configured to bend up to a 4 inch deep box, or can act as a straight sheet metal brake when all the fingers are in place, and can handle up to 16 gauge mild steel.

  • Model BB-4816: Box And Pan Brake, 48 inches long, 16 gauge capacity, includes counter weights and sturdy floor stand, and assortment of fingers, wt. is 550 lbs. - Price is $1885.00 delivered (includes shipping)


  • Features/Specifications - BB-4812 Box And Pan Brake

    • 48 Inches Wide Box And Pan Brake

  • Box And Pan Brake can handle up to 48 inch wide mild steel at a thickness of 12 gauge, and 16 gauge stainless steel

  • The unit is a very strong machine that can put perfect straight and tight bends into materials such as mild steel, aluminum, and stainless steel

  • This unit has heavy duty truss rods coupled to a electro welded all steel frame, and uses hardened fingers to produce minimal deflection even when bending a box up to 6 inches deep

  • The apron has precision lube for life bearings, and dual counter weights to assist any bend up to the maximum width and thickness capacity, making it very precise and easy to operate

  • The unit comes standard with a ridgid floor stand and 3 three inch, 2 four inch, 5 five inch, and 1 six inch hardened fingers. This combination of fingers allows the operator to build almost any size of box and pan required up to 48 inches wide and up to 12 gauge mild steel

  • The heavy duty apron has a solid stop rod system allowing the bending brake to be a repeatable machine for multiple production runs of the same item

  • The weight of the unit is almost 2000 lbs. (1985 lbs.), the heavily constructed all steel framework allows you to easily bend 12 gauge mild steel

  • Bending angle is 0 to 135 degrees

  • Beam adjustment is 1 inch, minimum reverse bend is 5/16 th inch

  • Shipping dimensions are 71 inches L x 34 inches W x 44 inches H

  • Model BB-4812: Box and Pan Brake, 48 inches long, 12 gauge capacity, includes: counter weights, sturdy floor stand, finger assortment - Price is $5680.00 delivered


  • Features/Specifications - BB-7212 Box And Pan Brake

    • BB-7212 Box And Pan Brake
  • Unit is a sheet metal bending brake 72 inches wide, a box and pan style brake that can be used as a straight brake or can be configured to make up to 6 inch deep pans utilizing a combination of 17 varying sized hardened fingers

  • This unit is heavily built, weighing almost 2500 lbs., and can easily bend up to 12 gauge thick mild steel or 16 gauge stainless steel

  • The apron is rigidly supported by a heavy duty truss rod system that eliminates any deflection throughout the span of the apron within the guaranteed capacity

  • Two heavy counter weights minimize operator effort by helping to lift the apron; effort is further reduced by the fact the apron is mounted on precision bearings, increasing production and accuracy of the bend

  • Bending angle from 0-135 degrees

  • Beam adjustment 1 inch

  • Minimum reverse bend of 5/16 inch

  • A positive stop rod system is employed when multiple repeatable bends are required

  • BB-7212 comes with a rigid bending stand that is the proper height to increase production and reduce operator error and fatigue

  • Model BB-7212: Box and Pan Brake, 72 inches long with 12 gauge capacity, includes counter weights and sturdy floor stand, includes finger assortment of 17 varying sizes all hardened for long life, wt. is 2426 lbs. - Price is $6695.00 delivered


  • Features/Specifications - BB-9612 Box And Pan Brake

    • BB-9612 Box And Pan Brake
  • This box and pan brake has 96 inches of useful bending width so it can bend a 4 ft. x 8 ft. sheet the long way, up to 12 gauge mild steel, and 16 gauge stainless steel

  • The unit has been ridgidly built to withstand deflection in the apron area

  • The apron is reinforced with very heavy truss rods coupled to its massive all steel frame that is electro welded to withstand use at maximum capacity day after day for decades, massive unit weighs approximately 3200 lbs.

  • The top apron has a 22 finger assortment of varying sizes to allow the operator to configure almost any box and pan up to a maximum depth of 6 inches

  • The fingers and the rail are hardened to produce extremely straight and tight bends for years of service, even in stainless steel

  • The bending apron has two massive counter weights to help assist the operator in fatigue free bending even at maximum capacity

  • The apron side shafts ride in precision "lube for life" bearings that improves tolerance and longevity of the apron

  • The unit comes mounted to a solid floor stand that improves efficiency and reduces operator fatigue

  • Bending angle from 0 - 135 degrees

  • Beam adjustment is 1 inch, minimum reverse bend 5/16 inch

  • Model BB-9612: Box And Pan Brake, 96 inches long, 12 gauge capacity, includes counter weights and sturdy floor stand and 22 piece finger assortment - Price is $8145.00 delivered


  • Features/Specifications - BB-12014 Box And Pan Brake

    • BB-12014 Box And Pan Brake
  • BB-12014 sheet metal box and pan brake has a 120 inch wide web width to allow for 4 ft. x 8 ft. sheets to be bent at 45 degree angles

  • Brake has 26 varying sized fingers that allow for metal bending of most size box and pans up to 6 inches deep

  • Massively built machine weighs 3418 lbs. and supports a heavy duty truss rod system for supporting the apron during maximum capacity bends

  • Massive all steel frame stabilizes the apron, to give you decades of serious use at the maximum capacity of 14 gauge mild steel, and 18 gauge stainless steel

  • This brake is perfect for the general fabrication shop or HVAC show and accepts the entire length of sheet metal at 45 degrees, allowing for angle crimps to add support to long duct pieces, and can handle up to 14 gauge mild steel.

  • The apron shafts ride in precision "lube for life" bearings, allowing for better tolerances and less operator fatigue. The apron is further supported by two massive counter weights, further reducing operator fatigue, even at maximum capacity

  • The individual hardened fingers can allow for straight bending or box and pan configurations

  • Bending angle is 0 - 135 degrees

  • Beam adjustment is 1 inch, minimum reverse bend is 5/16 inch

  • Shipping dimensions: 146 inches L x 34 inches W x 44 inches H

  • Model BB-12014: Box and Pan Brake, 120 inches long, has 14 gauge capacity in mild steel, includes counter weights and sturdy floor stand, and 26 piece finger assortment - Price is $9045.00 delivered


    • Click Here To Expand This To A Full Page Version

    Click On The Order Form Button Below For Ordering And Payment Information, Please Order In Writing Only Using Our Order Form.


    Order Form   Home Page/Index

    If Our Index Doesnot Appear On The Left Side Of This Page
    Then Click On The Home Button Above To See The Many Other Products We Sell

    Click On The Search Engine Symbol Below
    To Search Wikco.Com Using Our Search Engine

    Click To Search Through www.wikco.com

    For Sales or Technical Questions, Parts Information, Or To Check On An Order
    Please E-Mail us at: sales@wikco.com

    Wikco.com Inc.
    Please review all information on our web site
    If you have questions, E-Mail us at: sales@wikco.com
    Or Call 520-316-0446 Or Fax us at 520-316-0446


    Email Us at sales@wikco.com

    Copyright © Wikco.Com Inc., 1997-2008 All Rights Reserved